Davey SILENSOR POOL PUMP (including 400v 3 phase model) Instrukcja Użytkownika Pobierz pdf (Strona 3)

6 3

Power Connection

Davey Silensors

aresuitableforconnectiontoanominal240volt50Hzpowersupplyandare

equippedwithaexleadand3pinplug.Ifapoweroutletisnotavailablewithin3metresof

thepump,a3pinpowerpointinasafe,dryplace,mayneedtobeprovidedbyanelectrician.

Extensioncordsareunsafearoundpools-andshouldbeavoided.Ifthesupplycordofthis

product is damaged it must be replaced by the dealer or manufacturer, with genuine Davey

spares.

Pipe Connection

Asetofbarrelunionsareprovidedforconnectingtothepipingfromthepool.

ThepumpsaredesignedtoacceptthefollowingPVCpipesbyttingthepipetoeitherthe

inside or the outside of the union tail.

Model Inlet PVC Position Outlet PVC Position

SLS100-300 40mmpipe ID 40mm ID

or50mmtting OD 50mmtting OD

SLL150/200 40mmpipe ID 40mmpipe ID

or50mmtting OD 50mmtting OD

or50mmpipe ID 50mmpipe ID

SLL300/400 50mmpipe ID 50mmpipe ID

If the pump and lter are located below pool water level, it is necessary

to t isolating valves in the pipe between the pump and the skimmer box

and in the return pipe from the lter to the pool.

The ttings on this product are constructed of ABS. Some PVC jointing

compounds are incompatible with ABS. Check compound suitability

before use.

Warning! Ensure that an electrical isolation switch is located with easy

access so that the pump can be switched off in an emergency.

CAUTION:

In the interest of safety, we advise that all brands and types of pool pumps

must be installed in accordance with AS3000 wiring rules or equivalent

Davey Water Products recommends that all installations are tted with

earth leakage or residual current protection devices.

In accordance with AS 3350.2.41 we are obliged to inform you that this

pump is not to be used by children or inrm persons and must not be

used as a toy by children.

Water Quality

Maintaining balanced water chemistry is important to the life of your pool pump. This pump is

designed to be used with Pool & Spa water, balanced in accordance with Langlier Saturation

Index,withapHlevelofbetween7.2and7.8andisregularlytreatedwithachlorinesanitising

agentwiththelevelnotexceeding3000PPM.

Please consult your local pool shop regularly to have your water tested.

Three Phase Models

Three Phase Power Connection.

Threephasemodelsaredesignedforconnectiontoanominal400Vpowersupply,butmustbe

wiredwithacontactorwith‘quick-trip’overloadsseta4.3amps.

Davey recommend the use of overloads which also have the ability to detect “single phasing”

or “dropped phase” conditions in the power supply.

1. Removeboltandwasher(1)fromtherearofthepumpusinga½”socketandremovethe

rearpumpcover(2).

2. Carefully pull out the wiring from within the capacitor housing which is located on top of the

outercover(3)

3. Locatethewhiteterminalblockandunscrewthewiringfromthetestpowerleadsideofthe

block

4. ThreephaseSilensorpumpshavebeendesignedtoallowforconnectioneithersideofthe

capacitorcoverwith19mmaccessholes(4).Unscrewthepowerleadcablegrommetfrom

the side of the capacitor housing and remove the short test power lead from the pump

5. Threadthereplacementoperationalpowerleadthrougheitheroftheleadholesonthe

left or right hand side of the capacitor housing. Fasten the power lead into place with the

compression cable grommet. The unused hole can be sealed by inserting the plug that is

enclosed with the pump

6. Wiretheoperationalpowerleadintotheterminalblock,sameasdiscardedtestlead

7. Checkthatthethreephasewiringiscorrectbyconnectingtheleadtopowerandensure

thatthemotorshaftisturningcorrectlyinaclockwisedirection.Adirectionalarrowcanbe

foundontherearendshield(5).

8. Carefullytwiringandterminalblockbackintothecapacitorhousing,ensuringthatall

wiresarehousedsothattherearcoverdoesn’tpinchthewireswhentted

9. Replace rear pump cover and fasten with nut and washer.

NOTE: Three phase motors do not have capacitors tted in the capacitor

cover.

IMPORTANT NOTE:- THREE PHASE MODELS ONLY

BEFORE FINALISING WIRING CONNECTIONS, CHECK THAT THE MOTOR ROTATES

IN DIRECTION OF ARROW (CLOCKWISE WHEN THE SHAFT IS VIEWED FROM THE

WIRING CONNECTION END). TO ALTER ROTATION, CHANGE ANY TWO POWER

LEADS AT MOTOR TERMINALS.

1 2 3 4

Komentarze do niniejszej Instrukcji

Brak uwag

Davey SILENSOR POOL PUMP (including 400v 3 phase model) Instrukcja Użytkownika Strona 3

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Pompy Davey SILENSOR POOL PUMP (including 400v 3 phase model)